Logo

U1064 Engine Trouble Code

U1064 Engine

When you check engine light came on code U1064 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the U1064 OBD-II Diagnostic Network (U) Trouble Code. So you should chech it on our car models.

When the DTC check engine light comes U1064 code on the first you can check is the gas related maybe gas cap. Pull over, retighten it, and take a look at the cap to see if it has any cracks inside. Go on driving and to see if the check engine light turns off automaticly. On the other hand, you can buy a gas cap for about $4.5 at an auto parts store. All you need to do is take the old one take off and take on the new one. If you've already bought it to the store, you might as well just replace the cap. While not car-threatening, it's good to take care of this right away to improve gas mileage/km.

U1064 Code Meaning :

U
OBD-II Diagnostic Network (U) Trouble Code For Engine
1
Fuel And Air Metering
0
Injector Circuit Malfunction - Cylinders
6
Injection Pump Fuel Metering Control 'A' High (Cam/Rotor/Injector)
4
Clutch Position Sensor Circuit Malfunction

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

U1064 OBD-II Diagnostic Network (U) Trouble Code Description

U1064 engine trouble code is about Clutch Position Sensor Circuit Malfunction. Injector Circuit Malfunction - Cylinders and Injection Pump Fuel Metering Control 'A' High (Cam/Rotor/Injector) causes most of code U1064.

Reason For U1064 Code

The reason of U1064 OBD-II Engine Trouble Code is Injector Circuit Malfunction - Cylinders.

U1064 the main thing to check is to verify the operation of the VCT solenoid in the engine. You're looking for a sticking or stuck VCt solenoid valve caused by contamination. Refer to vehicle specific service repair manual to perform component tests for the VCT unit.

How To Repair U1064 Code

Before starting let's see U1064 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access U1064 code stored in the ECU.
  • Technicians will note U1064 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

As you idle at a light or before positioning your vehicle in gear and you see that your engine is starting to create strange sounds, switch your oil filter and also inspect the pressure regulator to attempt and adjust the error. If you struggle to start your vehicle and notice it fails to turn over right away, it can also indicate a defective fuel pressure regulator.

U1064 code is causing changes to the performance of the vehicle, this code will illuminate the Check Engine light, making it impossible to pass an OBD-II emissions test. Getting this problem addressed may also help you avoid expensive repairs to the clutch, primary pressure solenoid, and other parts of the transmission system later on.

Sometimes U1064 code comes with U106400 code.

Diagnosis Of Engine Error OBD Code U1064

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a U1064 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the U1064 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.
The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.